Code Corporation Code Reader 1.1 Bedienungsanleitung Seite 1

1Code Reader 1.1High-Density and Ultra High Density ImagerUser’s ManualThis manual is applicable for firmware versions 1200 and higher.

10Factory Default Settings for Keyboard Wedge The following are the factory default settings for Code Reader 1.1 High Density (HD) and Code Reader 1.1

11Your Code Reader has been properly configured before shipping and may not need to be reconfigured. If you wish to switch configuration to a keyboard w

12Read the following codes to add the corresponding prefix or suffix:Programming a Prefix or SuffixRead the Prefix None or Suffix None codes to turn the pre

13Chapter 3Code Reader 1.1 with Serial Port Interface

14EInstallation Instructions for a Serial Port Adapter Please read the following before setting up your Code Reader 1.1 with serial port adapter.A.

15Serial Port Interface - Default SettingsThe following are the factory default settings for Code Reader 1.1 High Density (HD) and Code Reader 1.1 Ult

16Your Code Reader has been properly configured before shipping and may not need to be reconfigured. If you wish to switch configuration to a serial por

17Read the following codes to add the corresponding prefix or suffix:Programming a Prefix or SuffixPrefix SuffixTab TabComma

18For advanced users only - Scan one of the following codes to set the word/character length.7 bit:8 bit:For advanced users only - Scan one of the f

19Scanning the following codes will set the baud rate for your Code Reader. The baud rate is the information transfer rate of data being passed betw

2Chapter 1 - Introduction 1.1 Table of Contents ...2-3 1.2 S

20Chapter 4Code Reader 1.1 with PCMCIA Card Interface

21Installation Instructions for PCMCIA Card Adapter 1. You will need to download software from the Code Corporation website. Installation instruct

22PCMCIA Card Interface - Default SettingsThe following are the factory default settings for Code Reader 1.1 High Density (HD) and Code Reader 1.1 Ult

23Your Code Reader has been properly configured before shipping and may not need to be reconfigured. If you wish to switch configuration to a PCMCIA Car

24Read the following codes to add the corresponding prefix or suffix:Programming a Prefix or SuffixPrefix SuffixTab TabComma

25Chapter 5Setting Targeting and Symbology Settings

26Data Matrix Data Matrix enabled: Negative Data Matrix enabled: Negative Data Matrix disabled: Rectangle-shaped Data Matrix enabled:

27PDF 417 PDF417 enabled: PDF417 disabled:Micro PDF 417 Micro PDF417 enabled: Micro PDF417 disabled:1-D Codes - Code 39, Code 12

28Set Reader ControlsEnable targeting dot laser: Disable targeting dot laser: Enable targeting circle laser: Disable targeting c

29Chapter 6Code Reader Specifications

3Chapter 5 - Setting Tageting and Symbology Settings 5.1 Symbology Settings ...

30Code Reader 1.1 HD - SpecificationsPerformanceThe Code Reader 1.1 - HD is for reading and decoding 2-D codes with elements as small as .007 inches (.

31Code Reader 1.1 UHD - SpecificationsPerformanceThe low-cost Code Reader 1.1 - UHD is for reading and decoding 2-D codes with elements as small as .00

32Chapter 7Maintenance and Troubleshooting

33Maintenance and TroubleshootingNote: The Code Reader 1.1 was designed for use in a light industrial or office setting. Ex-posing the Reader to hars

34Maintenance and Troubleshooting (con’t) Your Code Reader will perform a self-test every time it is powered up. You should see the light on the Code

35Code Corporation Customer Service and SupportCode Reader Questions or ProblemsIf you experience problems with your Code Reader or have questions ab

4Statement of Agency ComplianceThe Code Reader 1.1 can be set to use targeting lasers. If the targeting lasers are activated, do not stare into the

5Code Corporation - OverviewThe Code Corporation designs, develops and manufactures data capture and automatic identification technologies. The company

6Code Reader 1.1 - Overview The low-cost Code Reader 1.1 (figure 1.1) is an innovative, hand-held data capture device for reading and decoding high den

7Targeting and Reading Techniques1. Hold Code Reader about 2 - 4 inches above the code.2. Hold the Code Reader still - DO NOT SWIPE OR MOVE THE RE

8Chapter 2Code Reader 1.1 with Keyboard Wedge Interface

9Installation Instructions for Keyboard Wedge Ensure the power is off and unplug your keyboard.Simply follow the keyboard cord to where it plugs into